02Home & Garden · Updated
Exmark Lazer Z Charging System Explained
Short answer
The Exmark Lazer Z charging system uses a stator and regulator to recharge the battery while the engine runs
The charging system on an Exmark Lazer Z consists of a stator (alternator) mounted on the engine and a voltage regulator that converts AC to DC and maintains a safe charging voltage. It keeps the battery topped off during operation and powers the mower's electrical loads.
How the Charging System Works
The Exmark Lazer Z uses a flywheel alternator system. A stator is mounted under the flywheel, and as the engine turns, magnets on the flywheel pass by the stator’s coils, generating alternating current (AC). This AC is sent to a voltage regulator/rectifier, which converts it to direct current (DC) and regulates the voltage to a safe level for the battery and electrical system.
The regulator typically outputs around 13.5 to 14.5 volts when the engine is running at normal operating speed. This voltage is enough to charge the battery while also powering the lights, electric PTO clutch, and other accessories. The battery acts as a buffer, providing extra current when needed and storing excess power.
Components of the Charging System
- Stator: A coil of wire mounted under the flywheel. It generates AC voltage when the engine runs.
- Voltage regulator/rectifier: Converts AC to DC and regulates the output voltage. It may be a separate unit or integrated into the engine’s electrical system.
- Battery: Stores DC power and supplies it to the starter and electrical components.
- Wiring and connectors: Carry the current between components. Loose or corroded connections are a common cause of charging problems.
- Fuses: Protect the electrical system from overloads.
Common Symptoms of Charging System Problems
- Battery dies frequently: If the battery goes dead after a few days of normal use, the charging system may not be keeping it charged.
- Engine won’t start: A completely discharged battery won’t crank the engine.
- Lights dim or flicker: When the engine is running at idle, the charging output may be low, but at full throttle it should be steady.
- Battery smells like rotten eggs: Overcharging can cause the battery to vent hydrogen sulfide gas.
- Battery case bulges or leaks: Overcharging can damage the battery internally.
How to Test the Charging System
- Check the battery first: Ensure the battery is fully charged and in good condition. A weak or dead battery can mask charging system issues.
- Set the multimeter: Use a digital multimeter set to DC volts (20V range).
- Measure at the battery: With the engine off, the battery should read around 12.6 volts. Start the engine and run it at full throttle; the voltage should rise to between 13.5 and 14.5 volts.
- Test the stator output: Disconnect the stator connector and measure AC voltage across the stator leads. At full throttle, you should see roughly 20–30 volts AC (specific values vary by model; check your service manual).
- Test the regulator: If the stator produces AC but the battery voltage doesn’t rise, the regulator is likely faulty.
Always refer to the Exmark service manual for your specific model for exact test procedures and specifications. If you’re not comfortable with electrical testing, a dealer or small engine repair shop can do it.
Common Causes of Charging Failure
- Loose or corroded connections: The most common cause. Clean and tighten all battery terminals and connector plugs.
- Faulty voltage regulator: The regulator can fail, causing no output or overcharging.
- Failed stator: The stator windings can short or break, especially if the engine overheats or the flywheel is damaged.
- Blown fuse: A blown fuse can interrupt the charging circuit.
- Bad battery: A battery with a dead cell won’t hold a charge even if the charging system works.
Maintenance Tips to Keep It Charging
- Keep the battery terminals clean and coated with a thin layer of dielectric grease.
- Check the wiring harness for chafing, cracks, or loose plugs.
- Keep the engine and flywheel area clean to prevent debris from damaging the stator.
- Store the mower with a battery maintainer if you won’t use it for several weeks.
- Replace the battery every 3–4 years, or sooner if it shows signs of weakness.
Charging System vs. Battery Charger
The charging system on the Lazer Z is not a substitute for a battery charger. It is designed to maintain the battery’s charge while the engine is running. If the battery is completely dead, the charging system may not be able to bring it back to full charge, especially if you only run the mower for short periods. In that case, use a dedicated battery charger to fully recharge the battery, then let the charging system maintain it.
Safety and Precautions
- Always disconnect the negative battery cable before working on the electrical system.
- Never short the battery terminals with a wrench or other metal tool.
- Wear safety glasses when testing or cleaning the battery.
- If the battery is leaking or damaged, handle it with care and dispose of it properly.
- If you smell rotten eggs or see a bulging battery, stop using the mower immediately and have it inspected.
Frequently Asked Questions
Why does my Lazer Z battery keep dying?
The most likely causes are a faulty charging system (stator or regulator), a bad battery, or a parasitic draw that drains the battery when the mower is off. Test the charging output at the battery as described above.
Can I replace the stator or regulator myself?
Yes, if you have basic mechanical skills and the service manual. The stator is under the flywheel, so you’ll need a flywheel puller and a torque wrench. The regulator is usually easier to access. Follow the manual’s instructions carefully.
What voltage should the charging system output?
At full throttle, you should see about 13.5 to 14.5 volts DC at the battery. If it’s lower, the system isn’t charging; if it’s higher, the regulator may be overcharging.
How long should I run the mower to charge the battery?
It depends on the battery’s state and the charging output. A fully discharged battery may need several hours of running to reach full charge. For a battery that’s just been drained slightly, 30 minutes of running at full throttle may be enough.
Can a bad charging system damage the battery?
Yes. Undercharging can cause sulfation and shorten battery life, while overcharging can warp plates and cause the battery to overheat and vent gas. Both can permanently damage the battery.
Related
- Charging System Excessive Ripple: Causes & Fixes
- Charging System Diagram: How It Works
- Charging System Craftsman Riding Mower: How It Works
Further reading: Exmark Service Manual. Details can change, so check the official page for anything that matters to you. Spotted a mistake? Tell us. How we write an answer.