Trendingat

02Home & Garden · Updated

How to Boil Beans: Simple Steps for Tender Beans

Short answer

Soak dried beans, then simmer until tender, usually 1 to 2 hours

Boiling beans means hydrating them (soaking optional but recommended), then simmering in water until soft and creamy. The exact time depends on the bean type and age.

Soak time8–12 hours overnightExplained in: Step-by-Step
Simmer time1–2 hoursExplained in: Step-by-Step
You needWater and a potExplained in: Step-by-Step
Reading time5 min7 sections, about 1,140 words

What You’ll Need

  • Dried beans (or fresh shell beans)
  • Large pot (at least 4 quarts for 1 pound of beans)
  • Water (filtered or tap)
  • Salt (optional, add near the end)
  • Colander or strainer
  • Lid for the pot
  • Optional: aromatics like onion, garlic, bay leaf, or a piece of kombu

Step-by-Step

  1. Sort and rinse the beans. Spread the beans on a clean counter or baking sheet. Pick out any small stones, dirt clumps, or shriveled beans. Rinse well under cold running water in a colander.
  2. Soak the beans (optional but recommended). Place the rinsed beans in a large bowl or pot. Cover with 2–3 inches of cold water. Soak for 8–12 hours or overnight. For a quick soak, bring the beans to a boil for 2 minutes, then remove from heat, cover, and let sit for 1 hour. Drain and rinse after soaking.
  3. Add fresh water. Put the soaked beans in your pot. Add fresh cold water so it covers the beans by about 2 inches. Don’t reuse the soaking water—it contains oligosaccharides that cause gas.
  4. Bring to a boil. Place the pot over high heat. Once the water reaches a rolling boil, reduce the heat to low or medium-low to maintain a gentle simmer. A hard boil can split the beans and make them mushy.
  5. Skim off any foam. In the first 10–15 minutes of simmering, a frothy foam will rise to the surface. Use a spoon or skimmer to remove it. This helps reduce gas and keeps the cooking liquid clear.
  6. Add aromatics (optional). At this point you can add a halved onion, a couple of garlic cloves, a bay leaf, or a strip of kombu. These add flavor without interfering with cooking.
  7. Simmer until tender. Cook at a gentle simmer, partially covered, for 1 to 2 hours. Check the beans every 15–20 minutes. They are done when they are creamy inside with no chalky center. Taste one to confirm. If the water level drops below the beans, add hot water to keep them covered.
  8. Season near the end. Add salt (about 1 teaspoon per pound of beans) during the last 15–20 minutes of cooking. Acidic ingredients like tomatoes, vinegar, or wine should also be added late, as they can slow softening.
  9. Drain or use as needed. Once tender, drain the beans if your recipe calls for it, or use them directly in soups, stews, salads, or mash them. Reserve some cooking liquid (pot liquor) for soups or sauces—it’s full of flavor.

Common Mistakes

  • Adding salt too early. Salt can prevent beans from softening if added at the start. Wait until they’re nearly done.
  • Boiling too hard. A vigorous boil can split the skins and turn the beans to mush. Keep it at a gentle simmer.
  • Not soaking at all. While you can skip soaking, it extends cooking time and can lead to uneven texture. Soaking also reduces gas-producing compounds.
  • Using old beans. Beans that have sat in your pantry for years may never soften properly. If they’re very old, they may stay hard even after hours of cooking.
  • Adding acidic ingredients early. Tomatoes, lemon juice, vinegar, and wine can halt softening. Add them only after beans are tender.

Tips

  • Soak with baking soda. Adding 1/8 teaspoon of baking soda per pound of beans to the soaking water can help soften the skins, especially for hard water. Rinse thoroughly afterward.
  • Cook in batches. Beans freeze well. Cook a pound at a time and freeze in portions (with some cooking liquid) for up to 6 months.
  • Use a pressure cooker. If you have an Instant Pot or pressure cooker, you can skip soaking and cook beans in about 30–40 minutes. Follow your device’s manual.
  • Test for doneness by taste. The only reliable test is to bite a bean. It should be creamy inside, not chalky or grainy.
  • Keep the lid slightly ajar. This prevents boil-overs and allows steam to escape, keeping the cooking liquid from getting too cloudy.

Troubleshooting

  • Beans are still hard after 2 hours. This usually means the beans are old or the water is too hard. Add 1/4 teaspoon of baking soda to the pot (it raises pH and helps soften). Continue simmering. If they still won’t soften, they’re likely too old—accept them as crunchy or use them in a dish where texture doesn’t matter.
  • Beans are mushy and splitting. You boiled too hard or cooked too long. Next time, keep the heat low. For now, use the mushy beans in soups, dips, or refried beans—they’ll still taste fine.
  • Beans are foaming a lot. That’s normal. Skim the foam off with a spoon. If it’s excessive, you may have added too much water or the heat is too high.
  • Beans have a metallic taste. This can happen if you cooked them in an aluminum pot. Use stainless steel, enameled cast iron, or ceramic.
  • Cooking liquid is bitter. The foam wasn’t skimmed, or the beans were old. Skim diligently and consider discarding the first batch of water after a 10-minute boil (then add fresh water).

Frequently Asked Questions

Do I have to soak beans before boiling?

No, but soaking shortens cooking time and helps beans cook more evenly. It also reduces gas-causing sugars. If you skip soaking, expect to add 30–60 minutes to the cooking time.

How long do beans take to boil?

After soaking, most beans take 1 to 2 hours at a gentle simmer. Unsoaked beans can take 2 to 3 hours. The exact time varies by type, age, and altitude.

Can I boil beans without soaking?

Yes. Just add them to the pot with water, bring to a boil, then simmer. They’ll take longer and may be slightly less creamy, but they’ll still work.

Why do beans give me gas?

Beans contain complex sugars (oligosaccharides) that your body can’t digest. Soaking and discarding the water, plus skimming foam, helps remove some of these sugars. Eating beans regularly also helps your gut adjust.

Should I add salt to bean cooking water?

Add salt near the end of cooking, not at the beginning. Salt early can toughen the skins and slow softening. A teaspoon per pound of beans is a good guideline.

Can I use the cooking water from beans?

Yes, the leftover liquid (pot liquor) is flavorful and nutritious. Use it as a base for soups, stews, or to cook rice. Just remember it contains some of the gas-causing sugars, so start with a small amount.

Further reading: USDA FoodSafety.gov. Details can change, so check the official page for anything that matters to you. Spotted a mistake? Tell us. How we write an answer.