Trendingat

02Home & Garden · Updated

How to Remove Stainless Steel PEX Crimp Rings

Short answer

Cut the ring off with a rotary tool or crimp ring cutter

Stainless steel PEX crimp rings are removed by cutting them open with a dedicated crimp ring cutter or a rotary tool, then peeling them off the pipe.

Tool neededCrimp ring cutter or rotary toolExplained in: Step-by-Step
RiskDamaging the PEX pipe underneathExplained in: Step-by-Step
Best practiceCut at the crimp earExplained in: Step-by-Step
Reading time3 min7 sections, about 720 words

What You’ll Need

  • Crimp ring cutter (specifically for stainless steel PEX rings) or a rotary tool with a cutting disc
  • Safety glasses and work gloves
  • Adjustable wrench or pliers (optional, for gripping)
  • Utility knife (to clean any burrs)
  • New PEX ring and fitting (for reassembly)

Step-by-Step

  1. Turn off the water supply and drain the line to avoid water spraying when you cut the ring.
  2. Put on safety glasses and gloves to protect against metal shavings and sharp edges.
  3. Locate the crimp ear—the raised tab where the ring was squeezed. This is the weakest point.
  4. Position the cutter over the crimp ear. If using a rotary tool, fit a cutting disc and align it with the ear.
  5. Cut through the ear with steady pressure. For a manual cutter, squeeze the handles until the ear snaps. For a rotary tool, let the disc do the work—don’t force it.
  6. Peel the ring open using pliers or your fingers. Once cut, the ring should spread apart and slide off the pipe.
  7. Inspect the PEX pipe for nicks, scratches, or deformation. If damaged, cut out that section and use a coupling.
  8. Clean the pipe end with a utility knife to remove any burrs or debris.

Common Mistakes

  • Using a standard pipe cutter—it can crush the pipe or fail to cut the stainless steel.
  • Cutting too deeply—nicking the PEX pipe weakens it and can cause leaks.
  • Not draining the line—water will spray everywhere and make the cut harder.
  • Reusing the old ring—once removed, a crimp ring cannot be reused; it must be replaced.

Tips

  • If you don’t have a crimp ring cutter, a rotary tool with a thin cutting disc works well—just go slowly.
  • Cut at the ear, not the middle of the ring, because the ear is the thinnest and easiest to break.
  • After removal, sand any sharp edges on the pipe with fine grit sandpaper to avoid cutting yourself later.
  • Keep a spare PEX ring and fitting handy in case you need to reconnect immediately.

Troubleshooting

Ring won’t cut with a manual cutter: The cutter may be dull or not designed for stainless steel. Use a rotary tool instead.

Pipe got scratched: If the scratch is deep, cut out the damaged section and use a coupling. Shallow scratches can be sanded smooth.

Ring is stuck after cutting: Pry it open with a flathead screwdriver or pliers. If it still won’t budge, make a second cut on the opposite side.

Water leaks from the fitting after reassembly: Check that you used a new ring and that it’s positioned correctly over the fitting’s barb. Re-crimp with a proper PEX crimp tool.

Frequently Asked Questions

Can I reuse a stainless steel PEX crimp ring?

No. Once removed, the ring is deformed and cannot be reused. Always install a new ring.

What’s the difference between a crimp ring and a clamp?

A crimp ring is a continuous stainless steel ring that is compressed evenly, while a clamp (or cinch) has a raised ear and is tightened with a special tool. Removal methods differ slightly.

Can I use a hacksaw to cut the ring?

Yes, but it’s risky because it’s easy to nick the PEX pipe. If you use a hacksaw, cut at the ear and go slowly.

How do I know if my PEX pipe is damaged?

Look for deep scratches, cuts, or flat spots. If you can see the pipe wall is compromised, cut it out and use a coupling.

Do I need a special tool to remove the ring?

Yes, a crimp ring cutter or a rotary tool with a cutting disc is recommended. Pliers alone won’t cut through stainless steel.

Can I remove the ring without cutting it?

No, because the ring is compressed tightly around the pipe. Cutting is the only way to release it.

Further reading: none, this is general know-how. Details can change, so check the official page for anything that matters to you. Spotted a mistake? Tell us. How we write an answer.