Trendingat

02Home & Garden · Updated

How to Unclog a Pool Skimmer Line

Short answer

How to Unclog a Pool Skimmer Line

Reading time4 min7 sections, about 870 words

Unclogging a pool skimmer line restores proper water flow and filtration, preventing pump damage and cloudy water. Before you start, turn off the pool pump and ensure you have basic tools like a garden hose and a drain king bladder.

What You’ll Need

  • Garden hose with a threaded end
  • Drain king (bladder) or hose nozzle with a jet attachment
  • Plumber’s snake (auger) for stubborn clogs
  • Rubber gloves and safety goggles
  • Bucket and towels (for spills)
  • Pool skimmer plate and gasket (if replacing)

Step-by-Step

  1. Turn off the pump – Switch off the pool pump at the breaker to prevent air locks and damage. Close the skimmer valve if you have one.
  2. Remove the skimmer basket – Take out the basket and clean out any debris. This gives you direct access to the line.
  3. Insert a garden hose – Push the hose down the skimmer line as far as it will go. Turn on the water to full pressure. The water jet can dislodge leaves or small clogs. If water backs up, you’ve found the blockage.
  4. Use a drain king – Attach a drain king to the hose and insert it into the skimmer line. The expanding bladder seals the pipe, and the surging water pressure helps break up the clog. Run it for 30 seconds, then turn off and let the water drain.
  5. Try a plumber’s snake – If the water jet doesn’t work, feed a plumber’s snake into the line. Rotate the handle to break through the debris. Be gentle to avoid puncturing the pipe.
  6. Backwash the line – If you have a multiport valve, set it to “Backwash” and run the pump for a few minutes. This reverses flow and can push the clog out from the pump end.
  7. Check the pump basket and impeller – Sometimes the clog is at the pump. Open the pump strainer basket and clear any debris. Inspect the impeller for small objects like pebbles or twigs.
  8. Reassemble and test – Replace the skimmer basket, turn on the pump, and check for strong suction. If water flows normally, the clog is cleared.

Common Mistakes

  • Forgetting to turn off the pump – Running the pump while the line is blocked can cause air lock or damage the pump.
  • Using too much force – Pushing a snake too hard can crack the PVC pipe, leading to leaks.
  • Ignoring the skimmer weir – A stuck weir door can restrict flow, mimicking a clog. Check it moves freely.
  • Not cleaning the pump basket – A full pump basket reduces suction and can make you think the line is clogged.
  • Using chemicals to dissolve clogs – Drain cleaners can damage pool pipes and are ineffective on organic debris.

Tips

  • Prevent clogs – Use a skimmer sock or hairnet to catch fine debris before it enters the line.
  • Keep the water level up – If the water drops below the skimmer, air can enter the system, causing suction issues.
  • Flush lines regularly – Once a month, run a hose down the skimmer line for a few minutes to clear any buildup.
  • Use a leaf net – For heavy debris, use a leaf net over the skimmer basket to prevent large objects from entering.
  • Lubricate O-rings – Apply a silicone-based lubricant to the skimmer gasket to keep a tight seal.

Troubleshooting

If the clog persists after trying the steps above, consider the following:

  • Air in the line – If you see bubbles in the pump basket, there may be an air leak. Check the skimmer lid and O-ring for cracks.
  • Blockage at the main drain – The clog might be in the main drain line, not the skimmer. Try the same methods on that line.
  • Deep or hard clogs – For mineral buildup or roots, you may need a professional with a hydro-jetter. This is rare for residential pools.
  • Damaged pipe – If water leaks near the skimmer or underground, the pipe may be cracked. You’ll need to dig up and replace the section.
  • Pump won’t prime – After clearing the clog, if the pump won’t prime, check the strainer lid and ensure the pump is below water level.

Frequently Asked Questions

How do I know if my skimmer line is clogged?

Signs include weak suction at the skimmer, air bubbles in the pump basket, or water backing up out of the skimmer when you insert a hose.

Can I use a pressure washer to unclog the line?

No, a pressure washer can damage the pipe. A garden hose with a drain king is safer and effective.

What causes skimmer line clogs?

Leaves, twigs, small toys, and debris that pass through the skimmer basket. Also, mineral buildup over time can narrow the pipe.

How often should I clean my skimmer line?

There’s no set schedule, but if you notice reduced suction, check the line. Regular basket cleaning helps prevent clogs.

Can a clog cause pump damage?

Yes, running the pump with a blocked line can cause cavitation, overheating, and damage to the impeller or motor.

Should I call a professional for a stubborn clog?

If you’ve tried the steps above and the line is still blocked, a pool professional can use specialized tools to clear it without damaging the pipe.

Further reading: none, this is general know-how. Details can change, so check the official page for anything that matters to you. Spotted a mistake? Tell us. How we write an answer.