02Home & Garden · Updated
How to Unclog a Tub Drain (Step-by-Step)
Short answer
Clear the clog with a plunger, baking soda and vinegar, or a drain snake
Start with a plunger to dislodge the blockage; if that fails, use baking soda and vinegar to break down gunk, then finish with a drain snake to pull out hair and debris.
What You’ll Need
- Plunger (cup style works best for tubs)
- Baking soda
- White vinegar
- Boiling water (or hot tap water)
- Drain snake (or a wire coat hanger)
- Rubber gloves
- Old towel or rag
- Bucket or shallow pan
Step-by-Step
- Remove the drain cover. Most tub drains have a strainer or stopper that unscrews or pops out. If it’s a pop-up stopper, lift it and twist counterclockwise. Use a screwdriver if needed. Set aside the screws and cover so you don’t lose them.
- Try boiling water first. Pour a pot of boiling water directly down the drain. This can melt soap scum and grease that might be causing a slow drain. Wait 5 minutes, then run hot tap water to see if it flows better.
- Plunge the drain. Fill the tub with enough water to cover the plunger cup. Place the plunger over the drain and push down firmly, then pull up quickly. Repeat 10-15 times. The suction and pressure often dislodge clogs near the top. If water overflows, use a bucket to remove some.
- Use baking soda and vinegar. If plunging doesn’t work, pour 1/2 cup of baking soda down the drain, followed by 1/2 cup of white vinegar. Immediately plug the drain with a rag or stopper to keep the fizzing action inside the pipe. Let it sit for 15-30 minutes. Then flush with boiling water.
- Snake the drain. Insert a drain snake or a straightened wire coat hanger into the drain. Push it in until you feel resistance, then rotate and pull to hook hair and gunk. Do this several times, pulling out debris each time. Be gentle to avoid scratching the pipe.
- Flush with hot water. After clearing the clog, run hot water for several minutes to rinse away any remaining residue. This also helps confirm the drain is fully clear.
- Reassemble the drain cover. Once the water drains freely, replace the stopper or strainer and tighten any screws.
Common Mistakes
- Using chemical drain cleaners first. These can damage pipes and create hazardous fumes, especially if the drain is completely blocked. They also make it unsafe to use a plunger or snake afterward.
- Plunging without water. A plunger needs water to create a seal and pressure. Without it, you’re just pushing air.
- Forgetting to remove the stopper. If you plunge with the stopper in place, you’re not actually applying pressure to the drain.
- Snaking too forcefully. Pushing a snake too hard can puncture or damage PVC pipes.
Tips
- Prevent future clogs by using a drain strainer to catch hair and debris.
- Run hot water for 30 seconds after every shower to flush away soap scum before it hardens.
- Monthly maintenance: Pour a cup of baking soda followed by a cup of vinegar down the drain, let it fizz for 15 minutes, then flush with hot water.
- If you have a pop-up stopper, clean the hair wrapped around its hinge mechanism regularly.
Troubleshooting
If the drain still won’t clear after all steps, the clog may be deeper in the main drain line. Try a longer drain snake (25 feet or more) to reach further. If you suspect a main line blockage, check if other drains in the house are slow—if so, it’s a bigger issue that may require a plumber. Also, if you’ve used chemical cleaners, wait at least 24 hours before using a snake to avoid contact with corrosive substances. If water backs up into the tub when you flush a toilet or run another drain, that’s a sign of a main sewer line clog that needs professional help.
Frequently Asked Questions
How do I know if my tub drain is clogged or just slow?
A slow drain takes time to empty but eventually does; a clogged drain backs up immediately. If water pools in the tub and doesn’t drain at all, it’s clogged.
Can I use a plunger on a tub drain?
Yes, a cup plunger works well on tub drains. Make sure there’s enough water to cover the plunger cup and create a seal.
Is baking soda and vinegar safe for all pipes?
Yes, baking soda and vinegar are safe for PVC, metal, and older pipes. They’re a natural, non-corrosive alternative to chemical cleaners.
Why does my tub drain keep clogging?
Hair and soap scum are the most common culprits. Over time, they build up and form a blockage. Regular cleaning and using a strainer can prevent recurrence.
Can I use a wire hanger instead of a drain snake?
Yes, a straightened wire hanger works for clogs near the surface. Just bend a small hook at the end to catch hair, and be gentle to avoid scratching the pipe.
When should I call a plumber?
If you’ve tried plunging, baking soda and vinegar, and snaking, and the drain is still clogged, or if multiple drains are slow, it’s time to call a professional. They can use motorized augers or hydro-jetting to clear stubborn blockages.
Related
- How to Unclog a J-Tube: Step-by-Step Guide
- What Oriole Birds Eat: Diet & Feeding Tips
- Origin of Labor Day: History and Meaning
Further reading: none, this is general know-how. Details can change, so check the official page for anything that matters to you. Spotted a mistake? Tell us. How we write an answer.