Trendingat

02Home & Garden · Updated

SAP Cache Troubleshooting: Causes & Fixes

Short answer

Clear the buffer and increase memory allocation

SAP cache troubleshooting means clearing full buffers, raising memory limits, and checking for invalid entries that slow down the system.

Main causeBuffer overflow or low memoryExplained in: Steps to Fix Cache Issues
First stepCheck buffer statistics (ST02)Explained in: Steps to Fix Cache Issues
FixIncrease memory or clear bufferExplained in: Steps to Fix Cache Issues
Reading time3 min8 sections, about 740 words

What Is SAP Cache?

SAP uses caches (called buffers) to store frequently accessed data in memory, so the system doesn’t have to read from the database every time. This speeds up transactions and reduces database load. When a buffer is too small or gets filled with outdated entries, performance drops and you may see errors like “buffer overflow” or “no more space in the buffer.”

Common Cache Problems and Symptoms

Typical signs of cache issues include slow response times, program terminations (dumps), or errors like “TSV_TNEW_PAGE_ALLOC_FAILED” (memory allocation failure) and “DBTAB_NTAB_BUFFER_OVERFLOW.” You might also notice that a transaction runs slowly the first time but faster after—this is normal cache warm-up, but if it never speeds up, the buffer may be too small.

How to Check Cache Status

Use transaction ST02 (Buffer Synchronization) to see buffer usage. The screen shows each buffer (generic, single record, table, etc.) with columns for hits, misses, and “space allocated.” Look at the “Hit Ratio”—if it’s below 90% for table buffers, you may have a problem. Also check transaction ST04 for database buffers and AL08 for user sessions that might be holding locks.

Steps to Fix Cache Issues

  1. Identify the buffer: In ST02, note which buffer is full or has a low hit ratio.
  2. Clear the buffer: Use menu path Utilities → Clear buffer in ST02, or enter /$CUA in the command field to clear all buffers. This is a temporary fix but can restore performance immediately.
  3. Increase buffer size: Go to transaction RZ11 (profile parameter maintenance) and adjust parameters like rsdb/obj/buffersize (for table buffers) or ztta/roll_first (for roll memory). Be careful—increasing buffers consumes RAM, so monitor total memory.
  4. Check for invalid entries: Sometimes buffers hold obsolete data. Use transaction SE14 (table maintenance) to rebuild tables if needed, but only after consulting your BASIS team.
  5. Restart the application server: If the issue persists, a restart clears all buffers and often resolves memory leaks. Do this during a maintenance window.

Memory Management and Tuning

Cache issues often stem from insufficient memory. SAP uses a shared memory area called the Extended Memory (EM) and the Roll area. If you get memory allocation errors, check the operating system’s available RAM and the SAP instance’s memory parameters. Use transaction ST02 to see “Current Utilization” and compare with “Max. Allocatable.” If it’s consistently high, consider adding RAM or adjusting the em/initial_size_MB and em/max_size_MB parameters. Always test changes in a development system first.

Preventing Cache Problems

To avoid frequent cache issues, monitor buffer hit ratios weekly (ST02), set up alerts for buffer overflows, and schedule regular system restarts if needed. Also, avoid frequent table changes—each modification invalidates cached entries. For custom tables, consider using “Generic” buffering instead of “Single Record” if the table is large and rarely updated, as this reduces memory usage.

Frequently Asked Questions

Why does SAP run slow after a restart?

After a restart, all buffers are empty, so the first requests have to load data from the database, which is slower. This is normal and should improve as the buffer warms up.

What does “buffer overflow” mean in SAP?

It means the buffer area is too small to hold all the data being accessed, causing the system to constantly evict and reload entries. This leads to high database load and slow performance.

Can I clear the SAP cache without restarting?

Yes, you can clear buffers using transaction ST02 or by entering /$CUA in the command field. This is less disruptive than a restart but still affects performance temporarily.

How do I increase the table buffer size?

Use transaction RZ11 to change the parameter rsdb/obj/buffersize. The value is in KB, so for 100 MB you’d set 102400. After changing, you must restart the application server for it to take effect.

What is a good buffer hit ratio?

Aim for above 90% for most buffers. If it’s lower, you likely need to increase the buffer size or optimize your buffering strategy.

Further reading: SAP Help Portal. Details can change, so check the official page for anything that matters to you. Spotted a mistake? Tell us. How we write an answer.