Trendingat

02Home & Garden · Updated

Car Noise When Turning: Causes Explained

Short answer

Usually worn suspension or steering parts, or low power steering fluid

A noise when turning often comes from a failing CV joint, a worn wheel bearing, or low power steering fluid. The exact sound—clicking, grinding, or whining—points to the likely culprit.

Fluid checkpower steering levelExplained in: Power Steering System Issues
Reading time6 min9 sections, about 1,400 words

Why Turning Makes Noise: The Basics

When you turn the steering wheel, several systems work together: the steering rack or box, the power steering pump, tie rods, ball joints, wheel bearings, and (on front-wheel-drive cars) the CV joints. Each of these parts can wear out and produce a distinct noise. The key is to listen to the type of sound and when it happens—only while turning, or also when driving straight?

Turning increases the load on suspension and steering components because the vehicle’s weight shifts to one side. Worn parts that might be silent on a straight road often become noisy under that extra stress.

Common Noises and Their Causes

Here’s a quick guide to what you might hear:

  • Clicking or popping while turning – Most often a worn CV joint on a front-wheel-drive car. The rubber boot tears, grease leaks out, and dirt gets in, causing the joint to wear.
  • Grinding or growling – Usually a failing wheel bearing, especially if the noise changes with speed or gets louder when turning one way.
  • Whining or squealing – Often low power steering fluid or a worn power steering pump. The noise is most noticeable when turning the wheel at low speeds or when stopped.
  • Clunking or knocking – Could be a loose tie rod end, ball joint, or worn control arm bushing. This often happens over bumps or when turning sharply.
  • Rubbing or scraping – A brake rotor shield bent against the rotor, or a wheel rubbing against the fender liner (especially if the car is lowered).

These are the most common, but other possibilities include a worn steering rack, a loose serpentine belt (if the noise is under the hood), or even a stone stuck in the brake caliper.

How to Diagnose the Noise Yourself

You can narrow down the cause with a few simple checks, but always put safety first. Park on a level surface, set the parking brake, and chock the wheels.

  1. Check the power steering fluid – Locate the reservoir (usually near the engine) and check the level against the dipstick or marks. Low fluid can cause whining. Top up with the correct fluid type from your owner’s manual if low.
  2. Listen for the noise pattern – Drive slowly in a parking lot. Does it click when turning left but not right? That often indicates a CV joint on the opposite side.
  3. Inspect the CV boots – Look at the rubber boots on the drive shafts (front wheels). If they are cracked, torn, or leaking grease, the joint is exposed to dirt and will soon fail.
  4. Check for play in suspension parts – With the car off and wheels on the ground, grab the top of a tire and push/pull. Excessive movement could indicate a bad wheel bearing or ball joint. A loose tie rod can be felt by shaking the wheel side-to-side.
  5. Listen to the wheel bearings – Jack up the car (using a proper jack and stands), spin the wheel by hand, and listen for grinding. Also grab the wheel at 12 and 6 o’clock and rock it—play indicates a bearing issue.

If you’re not comfortable doing these checks, a mechanic can diagnose it quickly. But understanding the basics helps you communicate the problem.

CV Joints: The Usual Suspect

Constant velocity (CV) joints are found on the drive shafts of front-wheel-drive and many all-wheel-drive cars. They transfer power from the transmission to the wheels while allowing the suspension to move and the wheels to turn. Each joint is covered by a rubber boot that holds grease and keeps out dirt.

When a boot tears, grease flings out and water and grit get in. The joint then wears rapidly, producing a rhythmic clicking that gets faster as you accelerate and is most noticeable when turning. If you hear that, the joint is already damaged. You can sometimes replace just the boot if caught early, but once it clicks, the joint itself is usually worn and the whole axle assembly is replaced.

It’s a common misconception that you can drive indefinitely with a clicking CV joint. The joint can eventually fail completely, leaving you stranded and possibly damaging the transmission. If you hear clicking, have it inspected soon.

Power Steering System Issues

Most cars use hydraulic power steering, which uses a pump to pressurize fluid that assists your steering effort. Low fluid, a leak, or a failing pump causes a whining or groaning noise, especially when turning the wheel at low speed or at a standstill.

Check the fluid level regularly. If it’s low, there’s likely a leak—don’t just top it off repeatedly. Have the system inspected for leaks at the hoses, pump, or steering rack. Some newer cars use electric power steering, which doesn’t have a pump or fluid, so a whine there would point to a different issue, like the steering column motor.

Another less common issue is air in the power steering system, which can also cause noise. This can happen after a fluid change or if the fluid gets low. Bleeding the system (following the manual) often fixes it.

Wheel Bearings and Suspension Parts

Wheel bearings allow the wheels to spin with minimal friction. When they wear, they produce a grinding or growling noise that often changes with speed and gets louder when turning one way (because that loads the bearing). A bad bearing can also cause a slight vibration in the steering wheel.

Ball joints and tie rod ends connect the steering and suspension. When they wear, you might hear a clunk or knock when turning, especially over bumps. These parts are critical for control—if a ball joint fails, the wheel can collapse inward. Any clunking should be checked promptly.

Control arm bushings can also wear and cause a creaking or clunking noise during turns. These are rubber or polyurethane mounts that absorb road shock.

When to See a Mechanic

Some noises are minor, like a stone in the brake shield. But many indicate wear that will get worse. As a rule:

  • If you hear a new noise, get it checked soon. Driving on a worn CV joint or wheel bearing can cause more expensive damage.
  • If the noise is accompanied by a vibration, pulling to one side, or a warning light, stop driving and have it towed.
  • If you’re not sure what you’re doing, a professional inspection is worth the cost. It’s much cheaper than a breakdown or an accident.

Regular maintenance—like checking fluid levels and having suspension components inspected during tire rotations—can catch problems early.

Frequently Asked Questions

Why does my car click when I turn but not when I drive straight?

That’s the classic sign of a worn CV joint. The joint is flexed more during turns, causing the worn parts to click. It’s most noticeable on front-wheel-drive cars.

Can I drive with a noisy power steering pump?

You can drive for a while, but if the fluid is low, you risk damaging the pump and the steering rack. Check the fluid level and top up if needed, but have the leak fixed soon.

Why does my car make a grinding noise when I turn left?

If it’s a grinding or growling sound that gets louder when turning left, it’s often the right wheel bearing (because turning left loads the right side). But it could also be a brake issue.

Is it safe to drive with a bad wheel bearing?

No. A bad wheel bearing can cause the wheel to wobble or even seize, leading to a loss of control. It’s a safety risk and should be replaced immediately.

Why does my car squeal when I turn the steering wheel all the way?

That could be the power steering pump working hard at full lock, or a slipping serpentine belt. If it only happens at full lock and the fluid is full, it might be normal on some cars, but a persistent squeal is worth checking.

Further reading: NHTSA. Details can change, so check the official page for anything that matters to you. Spotted a mistake? Tell us. How we write an answer.