02Home & Garden · Updated
G56 Transmission Clutch Kit: What to Know
Short answer
A clutch kit for the G56 transmission includes the disc, pressure plate, and release bearing
A G56 clutch kit is a set of replacement parts—typically a clutch disc, pressure plate, and release bearing—designed to fit the Getrag G56 manual transmission used in heavy-duty trucks. Choosing the right kit depends on your truck's engine and how you use it.
What Is the G56 Transmission?
The G56 is a six-speed manual transmission built by Getrag and used in Ram heavy-duty pickups from 2005 to 2018. It was offered with the 5.9L and 6.7L Cummins diesel engines, and it’s known for being strong enough to handle high torque. The G56 replaced the earlier NV4500 and was itself replaced by the Aisin AS69RC automatic in later models, but many truck owners still prefer the manual for its durability and control.
Because the G56 is used in diesel trucks that often tow or haul heavy loads, the clutch has to hold a lot of torque. That’s why choosing the right clutch kit matters—a stock kit may not be enough if you’ve modified your engine.
What’s in a G56 Clutch Kit?
A standard clutch kit for the G56 includes three main parts:
- Clutch disc – the friction plate that connects the engine to the transmission.
- Pressure plate – the spring-loaded plate that presses the disc against the flywheel.
- Release bearing (also called throw-out bearing) – the bearing that disengages the clutch when you press the pedal.
Some kits also include the pilot bearing, which supports the transmission input shaft, and alignment tools. It’s a good idea to replace the pilot bearing at the same time, even if it’s not in the kit, because it’s cheap and you’re already in there.
How to Choose the Right Clutch Kit
The most important factor is the torque your engine produces. A stock 5.9L or 6.7L Cummins can be fine with an OEM-style clutch, but if you’ve added a tuner, bigger injectors, or other performance parts, you’ll need a clutch that can handle more torque.
Consider these factors:
- Engine torque – Know your torque level; stock, mild, or modified.
- Driving style – Towing, hauling, or daily driving all affect clutch wear.
- Clutch type – Organic (smooth engagement), ceramic (grippy but harsh), or dual-disc (for very high torque).
- Flywheel condition – If the flywheel is scored or warped, it must be resurfaced or replaced.
For most street trucks, a single-disc organic or ceramic clutch is a good balance. For serious towing or racing, a dual-disc kit is more expensive but holds more torque and still drives reasonably.
Common Problems and Misconceptions
One common misconception is that a heavier-duty clutch always lasts longer. In reality, a ceramic clutch can wear out faster if you do a lot of stop-and-go driving because it’s designed for high grip, not smooth engagement.
Another issue is the G56’s clutch pedal feel. Some aftermarket clutches have a much stiffer pedal, which can be tiring in traffic. If that matters to you, look for a kit that’s advertised as having a lighter pedal, or consider a hydraulic clutch upgrade.
A frequent problem during installation is forgetting to replace the pilot bearing. If it’s worn, you’ll get a vibration or noise, and you’ll have to drop the transmission again to fix it.
How to Replace the Clutch (Overview)
Replacing a clutch on a G56 is a big job that requires lifting the truck, removing the driveshaft, and dropping the transmission. Here’s a high-level look at the steps:
- Disconnect the battery and drain the transmission fluid to avoid spills.
- Remove the driveshaft and the transmission crossmember, then support the transmission with a jack.
- Unbolt the transmission from the bellhousing and slide it back to access the clutch.
- Remove the pressure plate and disc, then inspect the flywheel for heat cracks or scoring.
- Install the new disc and pressure plate using a clutch alignment tool to center the disc.
- Reinstall the transmission, refill the fluid, and bleed the clutch hydraulic system if needed.
If you’re not experienced with transmission work, this is a job best left to a professional. A mistake during installation can cause premature failure.
Cost and Where to Buy
Clutch kits for the G56 vary widely in price. A basic OEM-style kit is the most affordable, while a high-performance dual-disc kit costs significantly more. You’ll also need to factor in the cost of a new flywheel if yours is damaged, plus labor if you’re not doing it yourself.
You can buy kits from auto parts stores, online retailers, or directly from clutch manufacturers. Make sure the kit is specifically listed for the G56 and your engine year—some kits fit only the 6.7L, not the 5.9L.
Safety Tips
Working under a truck is dangerous. Always use jack stands, never rely on a jack alone. When you drop the transmission, be careful—it’s heavy and can crush you if it falls. Wear safety glasses and gloves, and use a transmission jack if you have one.
Also, after installing a new clutch, break it in properly. Most manufacturers recommend a break-in period of 500 miles of normal driving, avoiding heavy loads and hard launches. This helps the clutch disc and flywheel mate correctly.
Frequently Asked Questions
Will a G56 clutch fit a 5.9L and 6.7L Cummins?
Not always. The spline count and pressure plate bolt pattern can differ between the 5.9L and 6.7L. Always verify the kit is for your specific engine.
How long does a G56 clutch last?
It depends on driving habits and load. A stock clutch can last 100,000 miles or more with normal driving, but towing and aggressive use can shorten that significantly.
Can I install a G56 clutch myself?
If you have mechanical experience and the right tools, yes. But it’s a heavy, involved job, and mistakes are costly. Many owners choose a shop.
What’s the difference between organic and ceramic clutch discs?
Organic discs engage smoothly and are good for daily driving, but they wear faster under heavy torque. Ceramic discs grip harder and handle more torque, but they can be harsh on the drivetrain and pedal.
Do I need to replace the flywheel when I do the clutch?
Only if it’s worn, scored, or warped. If it’s in good shape, you can resurface it, but many prefer to replace it to ensure a perfect surface.
Related
- Dual Clutch Transmission Reliability Explained
- Dual Clutch Transmission Pros and Cons
- Dual Clutch Transmission Problems? Causes & Fixes
Further reading: none, this is general know-how. Details can change, so check the official page for anything that matters to you. Spotted a mistake? Tell us. How we write an answer.