Trendingat

02Home & Garden · Updated

How to Remove Stainless Steel PEX Clamps

Short answer

Use a PEX clamp removal tool or pinch the ears with pliers

Stainless steel PEX clamps are removed by squeezing the two ears together with a removal tool or locking pliers, then prying the clamp off the pipe.

Tool neededPEX clamp removal tool or pliersExplained in: Step-by-Step
TimeUnder a minute per clampExplained in: Step-by-Step
Watch outDon’t cut the pipeExplained in: Step-by-Step
Reading time5 min7 sections, about 1,150 words

Removing a stainless steel PEX clamp is a straightforward job once you know the trick. These clamps are crimped tight around the pipe, so you can’t just pull them off. The good news is that with the right tool and a little care, you can take one off without damaging the PEX tubing, which means you can reuse the pipe and simply install a new clamp.

Before you start, make sure the water supply is shut off and the line is drained. You’ll be working with the pipe under no pressure, which is safer and makes the clamp easier to remove.

What You’ll Need

  • PEX clamp removal tool (also called a PEX cinch clamp remover) – this is the fastest and safest option
  • Slip-joint pliers or locking pliers (vice grips) – a backup if you don’t have the specific tool
  • Flathead screwdriver – optional, helps pry the clamp off
  • Safety glasses – to protect your eyes from any spring-back

Step-by-Step

  1. Turn off the water and drain the line. Shut the supply valve and open a faucet downstream to release pressure and drain the pipe. This prevents water from spraying out when you remove the clamp.
  2. Identify the clamp type. Stainless steel PEX clamps (cinch clamps) have two small ears (tabs) sticking out from the band. These ears are what you’ll squeeze together. If you see a ring with no ears, it’s a crimp ring, which requires a different removal method.
  3. Position the removal tool over the ears. The PEX clamp removal tool has a jaw that fits around the two ears. Place the tool so the ears are fully inside the jaw, with the tool’s pivot point centered between them.
  4. Squeeze the handles together. This compresses the ears, which opens the clamp slightly. You should feel the clamp loosen its grip on the pipe. If you’re using pliers, grip the ears firmly and squeeze them together until they touch.
  5. Pry the clamp off. While keeping the ears squeezed, use a flathead screwdriver to gently pry the clamp away from the pipe. It should slide off easily. If it doesn’t, re-squeeze the ears a bit more and try again.
  6. Slide the clamp off the pipe. Once the clamp is loose, pull it off the end of the PEX tubing. If the clamp is stuck due to corrosion or debris, wiggle it back and forth while pulling.
  7. Inspect the pipe. Check the PEX tubing for any nicks, cuts, or deformation. If the pipe looks damaged, cut off the damaged section and use a fresh piece for the new connection.

Common Mistakes

  • Using a crimp ring removal tool on a cinch clamp. Crimp ring tools are designed for solid rings, not cinch clamps. Using the wrong tool can damage the clamp or the pipe.
  • Squeezing the ears with regular pliers and twisting. Twisting can tear the clamp or gouge the PEX. Always squeeze straight and pull straight off.
  • Forgetting to drain the line. You’ll end up with water everywhere, which can cause water damage and make the clamp slippery.
  • Cutting the clamp off with a hacksaw or rotary tool. This is dangerous because you can easily cut into the PEX pipe. Only cut as a last resort, and even then, score the clamp lightly and break it.

Tips

  • If you don’t have a PEX clamp removal tool, a pair of slip-joint pliers works well. Just make sure the jaws are wide enough to grip both ears.
  • Lubricate the clamp with a little dish soap if it’s stuck. This helps it slide off without damaging the pipe.
  • If you’re reusing the PEX pipe, cut off the old clamp and install a new one. Reusing a removed clamp is not recommended because the metal may have weakened.
  • Keep a spare clamp on hand so you can reattach the pipe immediately after removal if needed.
  • Work in a well-lit area so you can see the ears clearly and avoid slipping.

Troubleshooting

The clamp won’t loosen after squeezing. The ears might not be compressed enough. Try squeezing harder, or use a tool with more leverage. If the clamp is corroded, apply a penetrating oil and wait a few minutes.

The clamp breaks while you’re squeezing. This can happen if the metal is brittle. If the clamp snaps, use a flathead screwdriver to pry the broken ends apart and remove the pieces. Be careful not to scratch the pipe.

The pipe is damaged under the clamp. If you see cuts, gouges, or deep scratches, cut out the damaged section with a PEX cutter and install a coupling. Do not try to reuse a damaged pipe.

You can’t get the clamp off because it’s too tight. Some clamps are crimped very tightly. Use a PEX clamp removal tool designed for cinch clamps; it provides the right mechanical advantage. If you only have pliers, try using two pairs – one to squeeze the ears and another to pull the clamp off.

Frequently Asked Questions

Can I reuse a stainless steel PEX clamp after removal?

No. Once a clamp has been crimped and removed, it may not hold properly. Always use a new clamp for a new connection.

What’s the difference between a PEX clamp and a PEX crimp ring?

A PEX clamp (cinch clamp) has ears that you squeeze to tighten, and it’s removed by squeezing the ears again. A crimp ring is a solid ring that’s compressed with a crimp tool and must be cut off to remove.

Can I remove a PEX clamp with regular pliers?

Yes, slip-joint pliers or locking pliers can work if you grip the ears firmly and squeeze them together. It takes more effort than a dedicated removal tool, but it’s possible.

Will removing a PEX clamp damage the pipe?

If you use the proper technique and don’t cut or scratch the pipe, the PEX tubing should remain undamaged. Always inspect the pipe after removal.

Do I need to turn off the water before removing a PEX clamp?

Yes. Always shut off the water supply and drain the line to avoid a mess and to make the clamp easier to remove.

Can I use a heat gun to loosen a stuck clamp?

No. Heat can damage PEX tubing and cause it to fail. Use mechanical methods like squeezing and prying instead.

Further reading: none, this is general know-how. Details can change, so check the official page for anything that matters to you. Spotted a mistake? Tell us. How we write an answer.