Trendingat

02Home & Garden · Updated

How to Read Tire Numbers and Letters

Short answer

Tire numbers and letters tell size, type, load, speed, and date

The main string like P215/65R15 95H gives width, aspect ratio, construction, wheel diameter, load index, and speed rating. The DOT code at the end shows the week and year of manufacture.

Main stringP215/65R15 95HExplained in: Step-by-Step
ConstructionR means radialExplained in: Step-by-Step
Load index95 = 1,521 lbExplained in: Step-by-Step
Reading time5 min7 sections, about 1,200 words

What You’ll Need

  • A tire to inspect (on the vehicle or spare)
  • A flashlight if the sidewall is dirty or dim
  • A cloth to wipe off grime, if needed
  • Optional: your vehicle owner’s manual for recommended specs

Step-by-Step

  1. Find the main string of numbers and letters. Look on the sidewall for a sequence like P215/65R15 95H. It’s usually the largest and most prominent marking, often near the rim.
  2. Identify the tire type letter. The first letter (or letters) tells you the intended vehicle class: P for passenger car, LT for light truck, ST for special trailer, T for temporary spare, and no letter means European metric. For most cars, it’s P.
  3. Read the three-digit width. The number right after the slash (215) is the section width in millimeters, measured from sidewall to sidewall at the widest point. It’s not the tread width, but the overall width.
  4. Note the aspect ratio. The two-digit number after the slash (65) is the aspect ratio, meaning the sidewall height is 65% of the width. So a 215/65 has a sidewall height of about 140 mm. Lower numbers (like 40) mean a shorter sidewall and a sportier, stiffer ride.
  5. Check the construction letter. The next letter is almost always R for radial, meaning the internal cords run radially across the tire. You might also see D for diagonal bias-ply or B for belted bias, but radial is the standard for modern vehicles.
  6. Read the wheel diameter. The two-digit number after the construction letter (15) is the diameter of the wheel rim in inches. This must match your wheel size exactly.
  7. Note the load index. The next number (95) is the load index, a code that corresponds to a maximum weight the tire can carry at proper inflation. A 95 index equals 1,521 pounds. You can find a load index chart online or in the owner’s manual. Never use a tire with a lower load index than the vehicle requires.
  8. Check the speed rating. The final letter (H) is the speed rating, indicating the maximum safe speed. H = 130 mph, V = 149 mph, W = 168 mph, Y = 186 mph, and Z is for speeds above 149 mph. Common ratings: S (112 mph), T (118 mph), U (124 mph), H (130 mph), V (149 mph).
  9. Find the DOT code for the date. Look for the letters DOT followed by a string of characters. The last four digits are the week and year of manufacture. For example, 2319 means the 23rd week of 2019. If you see only three digits, the tire was made before 2000, and it’s likely too old to use.
  10. Check for additional markings. You may see M+S (mud and snow), an all-season symbol, or a snowflake icon for severe winter service. Also look for the maximum inflation pressure in psi and the maximum load in pounds, which are required by law.

Common Mistakes

  • Mixing up width and aspect ratio. The width is in millimeters, the aspect ratio is a percentage. They are not the same unit, and confusing them leads to wrong tire size.
  • Ignoring the load index. Using a tire with a lower load index than the vehicle requires can cause overheating and failure, especially when carrying heavy loads.
  • Assuming all speed ratings are the same. An H-rated tire is not the same as a V-rated tire. Using a lower speed rating than the vehicle’s recommendation can be unsafe at high speeds.
  • Misreading the DOT date. The date is the last four digits, not the first four. Some people look at the first numbers and think the tire is newer than it is.
  • Forgetting to check the spare. The spare tire also has a date code and may be old even if it looks unused.

Tips

  • Always replace tires with the same size and type as the original, or use the size recommended in the owner’s manual.
  • If you change wheel size, the tire size must change accordingly to maintain the same overall diameter. A tire size calculator can help.
  • Check the tire pressure monthly, as the load index and speed rating assume proper inflation.
  • If you buy used tires, always check the DOT date. Tires older than six years should be inspected by a professional, and many experts recommend replacing them after ten years regardless of tread.
  • When mixing tires, never put different sizes on the same axle. All four should ideally match.

Troubleshooting

  • Can’t find the main string? It’s usually on the outer sidewall, but sometimes it’s on the inner side. Check the other side of the tire or look near the bead (the edge that meets the rim).
  • The numbers are worn off. If the sidewall is scuffed, try wiping with a damp cloth. If still unreadable, look for the same size on the spare or in the owner’s manual. Never guess the size.
  • You see a letter like ZR. ZR is an older speed rating for tires rated above 149 mph. It’s often followed by a load index and a letter, like ZR 95W. The ZR is part of the construction/speed designation.
  • The tire has a P and also an LT. Some tires are marked with both, but the first letter indicates the primary use. P is for passenger, LT is for light truck. Use the one that matches your vehicle type.
  • What if the numbers don’t match the manual? The previous owner may have installed the wrong size. Consult a tire professional to determine the correct size for your vehicle.

Frequently Asked Questions

What does the “R” in tire size mean?

R stands for radial construction, meaning the internal cords run radially (from bead to bead) across the tire. It’s the standard for modern tires.

How do I find the tire date code?

Look for the DOT code on the sidewall. The last four digits are the week and year of manufacture, like 2319 for the 23rd week of 2019.

What is the difference between load index and load range?

Load index is a numeric code for a specific weight capacity, while load range (like SL or XL) is a letter that indicates ply rating and inflation pressure. Both are important, but the load index is more precise.

Can I use a tire with a higher speed rating?

Yes, a higher speed rating is generally safe as long as the load index is equal or higher. It may affect ride comfort and cost.

What does “M+S” mean?

M+S stands for Mud and Snow, indicating the tire is designed for some off-road and winter conditions. It’s not a severe winter rating; look for the snowflake symbol for that.

How long do tires last?

Tires typically last 6 to 10 years depending on use and storage, but the rubber degrades over time. Check the DOT date and replace any tire older than 10 years, even if the tread looks good.

Further reading: NHTSA. Details can change, so check the official page for anything that matters to you. Spotted a mistake? Tell us. How we write an answer.