02Home & Garden · Updated
How to Read a Tire Code: Sidewall Numbers Explained
Short answer
A tire code tells you size, type, load, speed, and age
The sidewall code is a mix of letters and numbers that reveal the tire's width, aspect ratio, construction, wheel diameter, load index, speed rating, and manufacture date. Once you know the pattern, you can read any tire in seconds.
What You’ll Need
- A tire on your vehicle or a spare (the code is on the sidewall, near the rim)
- Good light or a flashlight
- Optional: chalk or tape to mark where you started reading
Step-by-Step
- Find the code. Look on the sidewall of the tire, just above the rim. It’s a long string like P215/65R15 95H. If the sidewall is dirty, wipe it clean.
- Identify the tire type letter. The first letter tells you the intended vehicle class:
- P – Passenger car (standard cars, minivans, some light SUVs)
- LT – Light truck (pickups, vans, heavy SUVs)
- ST – Special trailer (for trailers only)
- T – Temporary spare (donut)
- No letter? That’s a Euro-metric tire, common on European cars; it’s similar to P but load capacity may differ.
- Read the three-digit width. The number right after the letter (e.g., 215) is the section width in millimeters – the widest point from sidewall to sidewall, not the tread. So 215 means 215 mm wide.
- Note the aspect ratio. The two-digit number after the slash (e.g., 65) is the sidewall height as a percentage of width. A 65 profile means the sidewall is 65% of 215 mm, which is about 140 mm. Lower numbers (like 40 or 45) mean a shorter sidewall – a sportier, stiffer ride.
- Check the construction letter. The next letter is almost always R for radial (the standard today). You might see D for diagonal (bias-ply) or B for belted – these are rare on modern vehicles.
- Read the rim diameter. The two-digit number after the construction letter (e.g., 15) is the wheel diameter in inches. So a 15 means the tire fits a 15-inch rim. This is critical – it must match your wheel exactly.
- Decode the load index. After the rim size, you’ll see a number (e.g., 95) followed by a letter (e.g., H). The number is the load index – a code that corresponds to a maximum weight the tire can carry at proper inflation. You’ll need a load index chart (widely available online) to convert: 95 = 1,521 lbs, 100 = 1,764 lbs, etc. Higher numbers = higher capacity.
- Decode the speed rating. The letter after the load index is the speed rating – the maximum sustained speed the tire is designed for. Common ones:
- S – 112 mph
- T – 118 mph
- H – 130 mph
- V – 149 mph
- W – 168 mph
- Y – 186 mph
- Find the DOT code for age. Look for the letters DOT followed by a string of characters. The last four digits are the week and year of manufacture. For example, 2319 means the 23rd week of 2019. If you see only three digits, the tire was made before 2000 (e.g., 239 = 39th week of 1999).
- Check for extra markings. You may see M+S (mud and snow), a mountain/snowflake symbol (severe snow service), or XL (extra load). These are additional capabilities, not part of the core code.
Common Mistakes
- Mixing up width and rim diameter. The width is in millimeters, the rim diameter is in inches. They are not interchangeable.
- Ignoring the load index. Using a tire with too low a load index can cause overheating and failure, especially when carrying heavy loads.
- Assuming all tires with the same size are the same. Load index and speed rating vary even within the same size.
- Misreading the date code. The last four digits of the DOT are the date, not the first four. Also, a tire older than 6-10 years is often recommended for replacement regardless of tread depth.
- Thinking the aspect ratio is a fixed measurement. It’s a percentage, so a 65 on a 215 tire is different from a 65 on a 235 tire.
Tips
- Take a photo of your tire code with your phone – it’s handy when shopping for replacements.
- Use an online tire size calculator to compare different sizes, but always consult a professional before changing sizes.
- Check your owner’s manual or the sticker on the driver’s door jamb for the recommended size and inflation pressure – that’s the size your vehicle was designed for.
- When buying new tires, match the load index and speed rating to your vehicle’s requirements. You can go higher, but not lower.
- If you have a spare tire, check its code too – many spares are temporary and have speed limits (often 50 mph).
Troubleshooting
- Can’t find the code? Check the inner sidewall (the side facing the car) – sometimes it’s printed there. Also check the spare tire in the trunk.
- The code is worn off? Look for a second imprint on the other side of the tire. If both are gone, you may need to visit a tire shop to measure the tire manually.
- See extra numbers like ’91V’? That’s the load index and speed rating combined – the same as the two-part code we covered.
- Confused by a letter before the size, like ‘P’ vs ‘LT’? P is for passenger vehicles, LT is for light trucks. Using an LT tire on a passenger car is okay if the load index is sufficient, but it may give a rougher ride.
- What if the tire has no DOT? That’s unusual – DOT is required in the US. If it’s missing, the tire may be imported or counterfeit; have it inspected by a professional.
Frequently Asked Questions
What does the ‘R’ in my tire code mean?
It stands for radial construction – the internal ply cords run radially (at 90 degrees) to the direction of travel. This is the standard for modern tires.
Can I use a tire with a higher speed rating than my car needs?
Yes, a higher speed rating is fine; it just means the tire can handle higher speeds. However, it may affect ride comfort and cost more.
How do I know the age of my tire?
Look for the DOT code and read the last four digits. For example, 3219 means the 32nd week of 2019. Tires older than 10 years should be replaced, even if they look fine.
What does ‘M+S’ mean?
It stands for Mud and Snow – a designation for all-season tires that meet certain tread criteria. It doesn’t mean they’re severe snow rated; look for the mountain/snowflake symbol for that.
Is the load index the same as the load range?
No. Load index is a numeric code for a specific weight capacity (e.g., 95 = 1,521 lbs). Load range (like C, D, E) is a letter system for ply rating, more common on truck tires.
Can I change tire size from what’s on the door sticker?
You can, but it’s not recommended without consulting a professional. Changing size affects speedometer accuracy, handling, and clearance. If you do, keep the overall diameter close to original.
Related
- Why Is the Sky Pink? Causes Explained
- How to Store Oxygen Cylinders Safely
- How to Get Rid of Voles in Your Yard
Further reading: NHTSA. Details can change, so check the official page for anything that matters to you. Spotted a mistake? Tell us. How we write an answer.